Top 10 common forklift mishaps ， forklift procedure ought to take notice of these matters ！.
Top 10 common forklift mishaps ， forklift procedure ought to take notice of these matters ！.
Blog Article
Don't undervalue the forklift at the office. If the operation is not good, there will be major mishaps in minutes, and there are several mishaps involving forklifts.
Case 1: The forklift freight obstructed the driver's sight, and the person ahead could not be located, causing a rolling crash.
Situation 2: In order to preserve the equilibrium of the forklift when lifting hefty items, the staff members utilized their body weight as the weight, which almost caused casualties.
Case 3: The size of the forklift cargo goes beyond the allowable size of the course and hangs on the roadside rack, which nearly causes an crash.
Situation 4: Forklift is speeding up and surrender during a turn.
Instance 5: The forklift vehicle driver did not observe the pedestrian, and the pedestrian did not observe the forklift.
Instance 6: The forklift raises the personnel illegally, the forklift vehicle driver does not use the seat belt, the forklift lifter drops and the vehicle driver is crushed when the forklift rolls over.
Situation 7: The forklift vehicle driver did not put on a safety belt and fell from the vehicle when it surrendered and was squashed.
Forklift operation must pay attention to these matters ：.
Start.
1. Prior to starting, observe the surroundings, and after verifying that there are no barriers that hinder the safety and security of driving, honk the horn first and after that begin.
2. For vehicles with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure (air pressure) gauge must be safe prior to starting.
3. When the forklift starts with a tons, the chauffeur ought to first verify that the lots is stable and trusted.
4. The begin needs to be slow and steady.
Driving.
1. When driving, the height in between the bottom end of the fork and the ground ought to be maintained 300mm-400mm, and the pole must be slanted backwards. .
2. Do not lift the fork expensive when driving. When getting in and leaving the job site or while driving, take care that there will certainly be no barriers overhead. When the lots is traveling, the fork must not be elevated too high, which will influence the security of the forklift. .
3. After dumping, the fork should be lowered to the regular driving setting before driving. .
4. When turning, if there are pedestrians or vehicles close by, the driving signal should be released first. High-speed doglegs are banned. High-speed sharp turns will cause the vehicle to lose lateral security and tip over. .
5. When the forklift is downhill, it is purely prohibited to turn off the fire and slide, and it is forbidden to brake suddenly while driving with tons unless there are unique conditions.
6. When the forklift is running, it needs to obey the web traffic rules in the manufacturing facility and should maintain a certain safety range from the vehicle in front. .
7. When the forklift is running, the tons has to be in the lowest placement that does not hinder the driving, and the gantry must be effectively slanted back. The tons shall not be raised other than when stacking or packing. .
8. The height of the lots need to not obstruct the driver's view. In special situations, when the thing affects the forward vision, drive at a reduced rate when turning around.
9. It is prohibited to switch on the ramp, neither to drive throughout the ramp. .
10. The secure driving speed of the forklift in the factory area is 5 km/h, and it should drive securely at a reduced speed when entering the manufacturing workshop area. .
11. When the forklift is raised, raised or driven, it is restricted for employees to depend on the fork to hold products and play a stabilizing role. .
12. If problems are discovered, they will be repaired and reported in a prompt manner, and they will never ever operate with diseases or conceal them.
filling and unloading.
1. When fork-loading things, the distance between both forks ought to be adjusted as required to make the tons of the two forks balanced and not skewed, and one side of the item must be against the rack. .
2. It is forbidden to work with a single fork or use a fork top or pull. In unique conditions, security warning signs have to be set up to remind bordering pedestrians. .
3. In the process of loading and dumping products, the forklift should be stopped with the brake. .
4. The speed of the automobile ought to be sluggish and constant. Beware not to roll the wheels on the dunnage, so as not to stretch the rolled items and hurt people. .
5. When utilizing a fork to fork the goods, the fork must be as deep as possible under the load, and it should be noted that the fork tip must not touch various other products or items. The load needs to be stabilized with minimal back tilt of the gantry to make sure that the tons does not move in reverse. The pole can be tilted ahead somewhat when the load is lowered to enable very easy placement of the tons and removal of the forks. .
6. It is forbidden to fork products at high speed and hit tough objects with the fork head. .
7. When the forklift is functioning, it is restricted for people to stand around the fork, so as to prevent the collapse of the goods and hurt people. .
8. Straining is prohibited, and it is restricted to utilize forks to raise employees to take part in high-altitude procedures to stay clear of high-altitude dropping mishaps. .
9. It is not permitted to utilize the brake inertia to slide, place, round or roll things. .
10. It is not permitted to make use of forks to pick, transform Stand-on Electric Pallet Stacker pallet dump.
Leaving .
1. It is restricted to leave the forklift when the products on the fork impend. Before leaving the forklift, you should discharge the goods or lower the fork structure.
2. Draw the hand brake deal with to dead or depress the hand brake button.
3. The engine is switched off and the power is removed. (Except for special conditions, such as the chauffeur does not leave the vehicle's line of sight and does not exceed 1 minute).
4. Remove the key. .
Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the look must be inspected, and gas, lubing oil and cooling water must be added.
2. Examine the security efficiency of beginning, running and braking.
3. Inspect whether the lights and horn signals are full and efficient.
4. Throughout the operation of the forklift, examine whether the pressure and temperature level are typical.
5. After the forklift is running, the exterior leakage must likewise be inspected and the seals need to be changed in time.
Forklift Safety Operation Specifications.
1. You must check prior to leaving the vehicle;.
2. When you run into a person in front of you throughout driving, you need to send out a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not exceed 5 km/h;.
4. When driving, the nadir of the cargo ought to be 0.3 Electric Forklift Truck for Warehouse m ~ 0.4 m in the air;.
5. The transforming should not be too sharp to avoid the tendency of " complimentary turning";.
6. Running up and down the slope should be slow-moving and uniform, and no turning on the incline is allowed.
7. Do not drive across the gradient. When the gradient is more than 10%, the vehicle needs to be driven in reverse when worsening;.
8. When the forklift employees carry the goods and progress, if they run into large or heavy goods and go to the motorist's line of vision, they should take the reversing workout
.
The "Eight Prohibitions" need to be adhered to in the procedure.
1. Single fork operation is not enabled.
2. It is not permitted to lift the goods for far away driving.
3. It is not permitted to get the goods by handing over the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and other dangerous chemicals with forks.
5. It is not permitted to use inertia pressure to grab the goods.
6. It is not enabled to use stopping force to expatriation round or easy-to-roll items.
7. It is not enabled to bring people to work with the pallet or fork, and it is purely restricted to stand under the fork after the fork is elevated.
8. Do not drive side to side on slopes
.
Parking is not allowed under the following conditions.
1. Contours, slim roadways, train crossings;.
2. Sections with a longitudinal incline above 5%.
3. When there is an challenge on one side of the roadway, the opposite side of the area with the same length as the barrier must be within 20 meters at each end.
Web：https://www.onenforklifts.com/
Email：info2@onen.cn
Phone：+86 13827083844